High Power Torch — Precision Photobiomodulation for Small Areas & Deep Penetration
This is the torch I reach for when precision matters. Five LEDs, four wavelengths, 200mW/cm² at skin contact — and a beam narrow enough to target a single acupuncture point, a specific joint, or a tooth socket. If you want whole-body coverage, you want a panel. If you want to put 810nm near-infrared exactly where the problem is, this is the tool.
(Norsk: Høyeffekt rødlysterapi-lommelykt for fotopunktur, presis lysterapi og dyp vevspenetrasjon)
🔬 Photopuncture — Lysterapi på Akupunkturpunkter
Photopuncture (fotopunktur på norsk) is the practice of applying concentrated red or near-infrared light directly to acupuncture points — the same points used in traditional akupunktur, but stimulated with photons instead of needles. Research in photobiomodulation suggests that applying light to these points can activate similar downstream responses to needle-based acupuncture, without the invasiveness.
What makes this torch particularly suited to it is the combination of factors that most devices don't deliver together: a narrow, concentrated beam, high enough irradiance to reach the depth of acupoint tissue, and 810nm×2 near-infrared — the wavelength that penetrates furthest and has the most documented effect on deep tissue biology.
Whether you're working through a structured fotopunktur protocol or simply applying light to the most relevant local point for a problem area, the torch gives you the precision that a panel physically can't. Read more about how light interacts with tissue on the photobiomodulation research page.
🎯 Point Precision
The beam is narrow enough to hold against a single acupoint — something that's impossible with a panel or mat. 30–90 seconds per point, moving through a protocol systematically.
📏 Depth That Reaches
810nm NIR penetrates 3–5cm into tissue. Acupuncture points along muscle meridians sit at depth — this reaches them. 670nm handles shallower points and periosteal tissue.
〰️ Continuous for Point Work
For fotopunktur protocols, continuous mode at contact is the standard approach. Apply for 30–90 seconds per point. Pulsed (10Hz) for points associated with pain and inflammation.
🦷 Intraoral Extension
With fibre optic attachment, point-specific work extends inside the mouth — tooth sockets, gum points, and the palate. The 670nm and 450nm wavelengths both have documented oral tissue applications.
⚖️ When You Need a Torch, Not a Panel
Both have their place. The honest answer is most people eventually want both — but here's how to decide where to start.
✅ The Torch Wins When…
- You want photopuncture / acupoint work
- You need precise treatment on one joint or injury
- You're treating inside the mouth, ears, or nasal passages
- You need something fully portable and travel-ready
- The problem is deep and small — knee, wrist, elbow, jaw
📋 A Panel Wins When…
- You want full-torso or whole-body coverage
- Skin health, collagen, and systemic benefit are the goal
- You want hands-free sessions while doing something else
- You're treating multiple large areas per session
Many people use the torch alongside one of the red light panels — the panel covers the broad picture, the torch handles specific problem spots.
🌈 Four Wavelengths — What Each One Does
All five LEDs fire simultaneously in every session. Here's what you're actually getting:
450nm — Blue
Antimicrobial properties relevant to oral therapy and surface conditions. Circadian-alertness applications for morning sessions. Complements the oral fibre optic use case.
620nm — Red
Skin-level work — collagen support, wound healing, surface inflammation. Penetrates approximately 8–10mm. Strong for superficial acupoints and scar tissue.
670nm — Deep Red
Strong overlap with CCO absorption peaks. Deeper than 620nm. Oral tissue, periosteal healing, and mid-depth acupoints. The workhorse wavelength for dental applications.
810nm × 2 — Near-Infrared ★
Two LEDs dedicated to 810nm — the wavelength most associated with deep tissue penetration (3–5cm+). The photopuncture workhorse. Joint, muscle, and deep meridian work.
⚡ 200mW/cm² at Skin Contact
High irradiance means effective dose accumulates quickly — shorter sessions deliver the same photon dose as longer sessions on lower-power devices. Built-in 6-minute shutoff prevents overexposure.
🦷 Fibre Optic Compatible
Accessories (sold separately) allow delivery inside the mouth, into the nasal cavity, and into the ear canal. Reaches tissue no external device can. Useful for tannkjøtt (gum) health, sinus issues, and ear conditions.
〰️ Continuous + Pulsed (10Hz)
Continuous for photopuncture and general tissue work. Pulsed for sessions targeting pain and inflammation — the 10Hz frequency is the most studied in photobiomodulation pain research.
🛡️ 2-Year Warranty
Double the standard on this torch — reflects the build quality and the reality that most people who buy it use it daily for joint and pain management protocols.
🎯 Narrow Beam Precision
170mm × 30mm, 210g. Hold it directly against the skin for photopuncture point work, or use at 2–5cm distance for slightly broader coverage. Panels can't do either of these things.
✅ CE & FCC Certified
Tested to European and international safety standards. Rechargeable battery included. Ships from Drammen — no import fees.
What People Actually Use It For
🎯 Photopuncture Protocols
Working through acupoint sequences for pain, inflammation, or systemic support. 30–90 seconds per point, torch held at contact. The precision format that made this the most-requested torch I've stocked.
🦵 Joint Pain
Kne (knee), ankles, elbows, wrists — hold directly against the joint for 1–3 minutes per area. The 810nm dose reaches joint tissue. The most common single use case among my customers.
💪 Muscle Recovery
Post-training use on specific muscle groups. The NIR wavelengths are what the recovery research is built around. Particularly useful for targeted spots that a panel treats too broadly.
🦷 Oral Therapy
With the fibre optic attachment — tannkjøttresesjon (gum recession), post-extraction healing, tannkjøtt (gum) health. The 450nm and 670nm wavelengths both have documented oral tissue applications.
👂 Ear & Sinus
Fibre optic into the ear canal and nasal passages — ear infections, tinnitus support, sinus conditions. Reaches tissue that no external device gets close to.
🩹 Localised Injuries
Specific injured areas — a torch lets you treat exactly that spot without illuminating the whole surrounding region. Especially useful for smaller body parts: toes, fingers, jaw, TMJ.
Usage — High Power Means Shorter Sessions
At 200mW/cm², effective photon dose accumulates faster than on lower-power devices. For photopuncture: 30–90 seconds per acupoint is the standard starting range. For joint and muscle work: 1–3 minutes per treatment area. The 6-minute auto shutoff is a safety ceiling — not a target time to hit.
- Photopuncture: 30–90 seconds per acupoint at contact, work through the protocol systematically
- Joint / muscle: 1–3 minutes per area at contact or 2–5cm distance
- Oral (fibre optic): 60–90 seconds per tooth or gum zone
- Daily use is fine — consistency matters more than session length at this irradiance
- Charge fully before first use — 3–4 hours via USB
Technical Specifications
| Wavelengths | 450nm · 620nm · 670nm · 810nm × 2 (5 LEDs total) |
| Irradiance at Contact | 200 mW/cm² |
| Irradiance at 2.5cm | 120 mW/cm² |
| Modes | Continuous + Pulsed (10Hz) |
| Auto Shutoff | 6 minutes |
| Dimensions | 170mm × 30mm |
| Weight | 210g (0.21kg) |
| Body Material | Aluminium alloy |
| Power | Rechargeable battery (USB) |
| Fibre Optic | Compatible — accessories sold separately |
| Certifications | CE & FCC Certified |
| Warranty | 2 years |
What's Included / Hva følger med
- 1× High Power Torch (450 / 620 / 670 / 810nm×2)
- Rechargeable battery + EU power converter
- USB charging cable
- User manual (Norwegian & English)
- Personalised usage guide from Dominic (by email)
- 2-year warranty
*Fibre optic accessories available separately for oral/nasal/ear therapy
🔗 Pair the Torch With
The torch handles targeted spot work and photopuncture protocols. These handle the broader picture:
- Half Body Gen 3 panel — torso coverage while the torch handles specific joints and acupoints
- Full Body OptiBio Mat — whole-body sessions, torch for targeted follow-up on problem areas
- Oral Care Mouth Guard — full-mouth coverage where the torch's fibre optic does single-point work
- Grounding & PEMF — the electromagnetic layer alongside the photonic one
- All portable devices — see the full range of targeted therapy tools
Why I Stock This One
This is the torch I'd buy if I was starting from scratch and wanted one device that could do the most. I use it on my knee after running, on specific acupoints for pain management, and with the fibre optic for dental work. The four wavelengths together mean I'm not leaving any therapeutic angle uncovered.
The thing I keep coming back to is precision. A panel is brilliant for what it does — but it can't do this. If you're considering photopuncture, treating a specific joint, or want a tool that travels with you, text me and I'll tell you whether this is the right fit or whether something else would serve you better.
📧 admin@lighttherapy.no · 📞 +47 951 47 478 (Text only)
🚚 Gratis Frakt over 3,000 kr · Ships from Drammen
No import fees. In stock.
🛡️ 30 Dagers Åpent Kjøp
Full refund within 30 days.
🔧 2-Year Warranty
Double the standard coverage on this model.
❓ Frequently Asked Questions
What is photopuncture and can I use this torch for it?
Photopuncture is the application of red or near-infrared light to acupuncture points instead of needles. The High Power Torch is well-suited for it: the narrow beam delivers a concentrated 200mW/cm² dose to a precise point, and the 810nm×2 near-infrared wavelengths penetrate to the depth where most acupoints sit in muscle and connective tissue. 30–90 seconds per point is the standard starting protocol.
Hva er fotopunktur og kan jeg bruke rødlysterapi i stedet for nåler?
Fotopunktur bruker konsentrert rødt eller nær-infrarødt lys direkte på akupunkturpunkter — de samme punktene som brukes i tradisjonell akupunktur, men uten nåler. Forskning antyder at fotobiomodulasjon på disse punktene kan aktivere lignende mekanismer som nålestikk. En kraftig lommelykt med 810nm nær-infrarødt lys er godt egnet fordi strålen er smal nok til å treffe enkeltpunkter nøyaktig, og fordi 810nm trenger dypt nok inn i vevet til å nå punktenes fysiologiske dybde.
Why does the High Power Torch use 810nm×2?
Two of the five LEDs are dedicated 810nm near-infrared — providing extra power at the wavelength most associated with deep tissue penetration. Doubling it increases the NIR dose without removing the other therapeutic wavelengths.
What are the four wavelengths?
450nm (blue), 620nm (red), 670nm (deep red), and 810nm×2 (near-infrared — two LEDs). All five LEDs activate simultaneously in every session.
Can I use it for oral or ear therapy?
Yes. Fibre optic accessories (sold separately) allow safe delivery to gum tissue, nasal passages, and the ear canal. The torch's 450nm and 670nm wavelengths both have documented oral applications alongside the NIR.
Should I use continuous or pulsed mode for photopuncture?
For photopuncture and acupoint work, continuous mode at contact is the standard approach — 30–90 seconds per point, moving through the protocol. Pulsed (10Hz) is worth trying for points associated with pain and inflammation. Most protocols start with continuous and experiment from there.
How does 200mW/cm² affect how long I should use it?
Higher irradiance means effective dose accumulates faster. For photopuncture: 30–90 seconds per acupoint. For joint and muscle work: 1–3 minutes per area. The 6-minute auto shutoff is a safety ceiling — the goal is not to hit it every session.
Is daily use safe?
Yes. Red and NIR light therapy is non-thermal and non-ionising at these wavelengths. The research base for photobiomodulation safety is well-established. The 6-minute auto shutoff prevents overexposure in any single session.